What does DSI FLT light mean?

Posts: 10,086. DSI means direct spark ignition. FLT means fault. That means it tried to ignite the burner on the water heater but failed.

What does FLT mean on RV control panel?

FLT means fault. During normal operation the light should come on when you turn on the (propane) switch for the water heater. Once the water heater fires up correctly, the light should go out.

What does DSI fault mean in my camper?

DSI fault means that the gas did not ignite during start up.

What does DSI mean on a water heater?

Direct Spark Ignition
A step-up from the manual LP gas water heater is the LP gas model with Direct Spark Ignition or DSI. What DSI means is, rather than going outside to manually light the water heater with a match or striker you light it from inside the RV at the touch of a switch.

What does DSI indicator mean?

Daily Sentiment Index at Extremes: Typical Behavior The DSI can be used as a timing indicator when combined with other indicators and as part of an overall trading model.

Do RV water heaters have a reset button?

Look for the DCI lights on the panel. If they are lit, you will need to go outside and push the reset buttons on the water heater. If this does not fix the issue, additional RV water heater troubleshooting will be needed. To get a better look at the water pump, take the cover off of the bottom heat element.

Why Is My RV water heater reset light on?

It could mean that your water heater pilot blew out from the wind or an air pocket in the line. Try shutting off the switch, counting to three, and turning it back on. You should hear the heater catch and the light should go right out.

Can I run my RV water heater on gas and electric at the same time?

As mentioned before, you can choose to use both the propane and electric options together if you happen to have a heater with both. Doing so will cut down a bit on the time it takes to warm your water.

Why does my water heater keep needing to be reset?

If your water heater reset button keeps tripping, one of your heating elements may be broken or worn out. As this component is used to heat water, your hot water heater won’t work without it. When the reset button on a water heater thermostat keeps tripping, the metal casing of the heating element may have cracks.

Why Is My RV water heater not getting hot?

The reasons could be a malfunctioning thermostat, a broken or damaged dip tube which would allow cold water to mix with the hot water at the top of the water heater, or having the water temperature set too low. Sometimes it just boils down to having a water heater tank that’s too small for your needs.

Should I leave my RV water heater on all the time?

RV Electric Water Heaters Just like in your home, it is safe to leave your electric powered RV water heater on all the time whether stationary or on the road. There are other downsides such as cost and environmental impact of fuel consumption – but safety should not be a concern.

Should I turn my RV hot water heater off at night?

Just like in your home, it is safe to leave your electric powered RV water heater on all the time whether stationary or on the road. There are other downsides such as cost and environmental impact of fuel consumption – but safety should not be a concern.

What happens when the DSi FAULT light comes on?

However about 4 hours later, the DSI fault light came on again. When the light comes on, this not only shuts down the gas side but the electrical as well. When the light is off, both sides work normally.

What does DSi mean on a gas fireplace?

The DSI system removes that danger as it shuts off the gas flow when certain issues are detected like the gas failed to light. Often, the DSI control will try 3 times to light the gas, and when it fails all three times it locks out the gas supply.

Where is the DSi and Flt light on a Kenmore Elite washer?

There is a light with “DSI” above it and “FLT” below it. This light is between the switches for the gas and electric switches for the hot water heater.

What is a DSi fault on a water heater?

What is a DSI fault? The DSI letters stand for direct spark ignition. That is the device that helps add the flame to the gas in order to heat your water. When this fault code appears on your water heater, it generally means that no gas or propane is coming through the line. To learn more about the DSI fault code just continue to read our article.