Should there be water in the EZ Trap?

EZ Traps are part of your HVAC’s drainage system, so they are designed to drain water, so if you see water inside your EZ Trap, rest assured it’s normal. If you notice that your EZ Trap is filled with water, or even overflowing, then you have a problem that is likely tied to a clog somewhere in your drainage system.

How do I reset my EZ trap float switch?

With a shop vacuum suck the water out of the secondary pan to a level low enough to allow the switch to go down to its lowest position. Once the water level is low enough for the switch to reset, the system should come back on.

How do you clear a clogged condensate pipe?

In Winter, your condensate pipe may freeze and become blocked. This can easily be fixed by using a hot water bottle, or pouring warm water over the pipe itself.

What can I do about condensation on my air ducts?

Try to reduce the humidity level in the air near the air ducts. You can go for a dehumidifier if that helps to reduce the condensation. Unblock any ducts that are restricting airflow and have them cleaned regularly. Regularly clean your air filters and change them once every three months.

How often should you flush a geothermal system?

If you have an open loop system with your geothermal unit, also known as pump and dump, you should have your coax heat exchanger cleaned every year or two.

How do you unclog a furnace pipe?

Many times the clogged drain can be cleared with wet/dry vacuum suction. You can also try removing the clog with a plumber’s snake. Use the access port to flush the drain with white vinegar, diluted hydrogen peroxide, or hot water and a drop of dish soap.

Why is my furnace dripping so much water?

The Possible Causes of Your Leak You might have a clogged condensation drain or tubing, a break in the condensation line, or issues with the condensate pump, if you have such a pump. A standard-efficiency furnace extracts some heat from the combustion gases and quickly vents them out the exhaust or flue pipe.

How do I know if my condensate pipe is clogged?

Signs that your condensate trap is blocked can include a faint gurgling noise coming from your boiler, or an unusual sound coming from the flue outside your home. If the trap does need to be cleaned, your heating engineer will remove it, rinse it out thoroughly, refill it and then refit it.

What causes a blocked condensate pipe?

Tiny bits from the heat exchanger may be corroded and can end up in the sump and eventually in the condensate trap. This, in turn, will stop the flow of condensate, which will go back up into the bottom of the heat exchanger afterwards. And this is how you get a blocked condensate trap!

Why is my ductwork full of water?

There are a few common reasons for water in air ducts. Moisture can be a sign of low duct temperature. During the heating season, unused air-conditioning ducts located in unheated rooms can collect moisture. Moisture can also collect in the summer if cool air passes through a duct in a room that isn’t air-conditioned.

Why are my AC vents dripping water in the winter?

Condensation usually occurs when warm, moist air contacts a cold surface. Moisture will form on the cold surface and drip down. You often see it on old metal windows that are not made with insulated glass. The way to avoid condensation is to keep the warm air away from the cold surface.

How many years does geothermal last?

Geothermal heat pumps last significantly longer than conventional equipment. They typically last 20-25 years. In contrast, conventional furnaces generally last anywhere between 15 and 20 years, and central air conditioners last 10 to 15 years.

Why does my float switch keep tripping?

If your AC float switch keeps tripping, you probably have an AC drain pan that’s full. You’ll need to empty the water, and with the right tools, you can do this yourself. You should also consider why the pan became full in the first place.

How do I clean the EZ trap?

OK, let’s clean the EZ Trap. Step 1: Remove the float switch from the EZ Trap. Step 2: Have a cup or bowl ready when removing the cap. Step 3: Remove the brush from the holder and insert all the way in until it stops. Step 4: Push the brush through the EZ Trap. Step 5: Return the brush to the holder; Replace the cap.

Why do I need an EZ trap?

EZ Traps are an easy way to prevent very costly water damage. Besides monitoring the EZ Trap; annual maintenance will help prevent drain line clogs as well. If your system is currently without an EZ Trap what are you waiting for?

What happens when you fill the EZ trap with water?

If a clog does form, when filled with water the float will signal the system to turn off. This will prevent water from overflowing the drain pan. Once the EZ Trap is clear of the clog simply turn your system back on. Believe us you’ll be happy to feel that cool air again.

What are the grouped product items for the EZ trap?

Grouped product items Sku Name 83113 EZ Trap 113 3/4″ CRS Trap Kit No Brush 83114 EZ Trap 113B 3/4″ CRS Trap Kit W/Brush 83224 EZ Trap 220 Series Overflow Switches EZT 83225 EZ Trap 220 Series Overflow Switches EZT