How fast was the 1980 Turbo Trans Am?

According to the ProfessCars™ estimation this Pontiac would accelerate 0-60 mph in 8 sec, 0-100 km/h in 8.4 sec and quarter mile time is 16.1 sec. This car is 4999 mm / 196.8 in long, 1854 mm / 73 in wide and 1257 mm / 49.5 in high.

How much horsepower does a Turbo Trans Am have?

What’s the performance of the Pontiac Trans Am 20th anniversary Turbo?

Engine	3.8-liter SFI turbocharged V-6
Power	250 HP
Torque	340 LB-FT
0 to 60 mph	4.6 seconds
Transmission	four-speed automatic

How fast was the Turbo Trans Am?

For a brief time, this became America’s quickest and fastest production car and went on to pace the Indianapolis 500 race. According to independent runs, the Turbo Trans Am (TTA) could hit 60 mph (97 kph) in just 4.6 seconds, before maxing out at 162 mph (260 kph).

What transmission came in the 1980 Turbo Trans Am?

Built in the Van Nuys, California, plant (though unable to be sold in the Golden State legally: The Trans Am Turbo was a 49-state car, unable to meet California’s onerous smog regs), all were equipped with mandatory Turbo 350 non-lockup automatic transmissions, 3.08 rears, and air conditioning.

Is the Pontiac 301 a good engine?

The 301 is a weak motor and one of Pontiacs worst. mods/parts are darn near non-existant for that motor.

Is a Pontiac 389 a big block?

By varying bore, stroke, journal size and deck height, Pontiac offered their sole V8 Uniblock in displacements ranging from 265 to 455 cubic inches, the most renowned being the 326, 389, 400, 421, 428 and 455. Bear in mind that a big block is not necessarily a one-size-fits-all holy grail.

What engine was in the Movin On truck?

The Movin’ On television show ran for two seasons (1974 to 1976) using the Kenworth, powered by a VT903 Cummins with a 13-speed transmission and 3.70 rears.

How much horsepower did the Bandit car have?

Under the hood of the incredible Trans Ams used for the film sat a 400 ci V8 engine, which pushed out somewhere in the realm of 200 horsepower. Torque numbers were a lot higher at around 320 ft/lbs. Unlike many iconic muscle cars that we’ve all come to know and love, the Trans Am was not that fast.

How much HP does a 455 olds have?

As was common practice at the time, Oldsmobile manufactured a number of 455 variants, altering compression ratios, piston designs, and intakes depending on which application the motor was used for. Factory horsepower ratings ranged from 310 all the way up to 400 ponies, with 500 lb-ft the most common torque figure.

How much horsepower is in a 455?

They rated the standard issue 455 at 350 HP and the high-performance stage I version at 360 HP. This engine had a short run starting in 1970. In 1975 General Motors started using the same engines across the different divisions and platforms.

How much horsepower can you get out of a 389?

The Tempest 389 engines were also known as “420-A” motors and came with higher compression as well as better performance options. These engines were available up through 1962 and produced up to 348 horsepower which was the highest power output a factory 389 engine would ever see with the Tri-Power carb setup.

How much horsepower does a 389 Tri Power have?

325 horsepower
The burly 389 cubic-inch eight-cylinder engine, borrowed from Pontiac’s full-size offerings, put down an impressive 325 horsepower while flying in the face of GM’s then-recent prohibition on engines larger than 330 cubic inches in intermediate-sized vehicles.

Why was Coors illegal in Smokey and the Bandit?

Coors didn’t pursue distribution east of Texas, though, contributing to the lager’s massive – and sometimes illegal – following. Coors’ exclusivity prompted smugglers to seek out the beer, even inspiring the plot of the 1977 classic film Smokey and the Bandit.

Who owns the truck from Smokey and the Bandit?

Seems trucker Neil Ashworth of Huddersfield, England, is now the owner of a 1985 Kenworth W900B he purchased from another U.K.-based owner. After researching the vehicle’s history here in the U.S., he realized the truck had in fact been part of the Burt Reynolds co-owned Skoal Bandit NASCAR team back in the late 1980s.

How powerful is a 1980 Turbo Trans Am?

For those Trans Am owners who were used to the more powerful Trans Ams of the 1970s, the Turbo Trans Am was a letdown. However in comparison to all other American performance offerings of 1980, the Turbo Trans Am was top dog. Most new performance cars in 1980 had well under 200 horsepower.

What are the dimensions of a 1980 Pontiac Trans Am?

The 1980 Pontiac Firebird Trans Am measures 73.00 inches in width, The 1980 Pontiac Firebird Trans Am measures 196.80 inches in length, and has a wheelbase of 108.20 inches.

What kind of transmission does a 1979 Trans Am have?

The 1979 W72 was mandatory with a 4-speed manual transmission with a factory Hurst shifter and 3.23 rear axle ratio. For those Trans Am owners who were used to the more powerful Trans Ams of the 1970s, the Turbo Trans Am was a letdown.

What was it like to drive a 1980 Turbo Ta?

JM January 7, 2018 at 2:44 am I owned a 1980 Turbo TA. Loved the car. The handling was one of the best I ever drove. I called it “point it and punch it”. After you got used to the turbo lag, It was a fun car to drive. I would also from time to time put half av gas and half premium in the tank and the car would fly.