Which way do Bilstein rear shocks go?
Which way do Bilstein rear shocks go?
Bilstein does have some shocks that do have the boot on the bottom of the shock and the same size mounting eyes on each end. As a general rule with all Bilstein shocks, you should pay attention to the label. Bilstein tech advises that you should always mount your shocks so that the Bilstein logo is right-side up.
Which way do you install Bilstein shocks?
Can you install Bilstein shocks upside down?
The shock has 12mm eyes on each end, so it could be mounted either way. The correct way to mount it is as shown with the boot down and the label facing so it is not upside down. So, If you are not sure which way is up on your shocks or wonder if you can mount them either way, always look at the Bilstein logo.
Can shock absorbers be mounted upside down?
Some people say that monotube or gas pressurize shocks can be mounted upside down, however in time they will develop and extra inch or more of piston travel that has little to no dampening effect whatsoever. Ultimately: don’t mount shocks upside down just because it looks cool.
Can you install shocks wrong?
The wrong height for the spring plate can result in the spring having no pre-tension. On systems with a side load spring the spring can become stuck or fall out. The shock absorber goes into the compression stop, has higher wear on the buffer and does not allow sufficient bump travel.
What happens if you install shocks upside down?
With oil charged the oil will go down, and this can change the valving of the shock if its upside down. It does not matter with gas charged shocks, it only matters with oil charged shocks. With oil charged the oil will go down, and this can change the valving of the shock if its upside down.
Is there a top and bottom for shocks?
The outer tube is used to store excess fluid. The upper mount of the shock absorber connects to the vehicle frame. This upper mount is called the piston rod, and at the bottom is the piston. Notice that this piston rod passes through a bushing and a seal at the upper end of the pressure tube.
What happens if rear shocks upside down?
Does direction of shock matter?
Based on my experience it doesn’t matter. I have tried both directions on my bike and I didn’t notice any slightest difference. Simply choose the position which is most convenient and take care that the suspension movement can not cause any damage to the shock or the bike.
Should I be able to compress a shock by hand?
You cannot judge the strength or condition of a shock/strut by hand movement alone. The force and speed generated by a vehicle in operation exceeds what you can accomplish by hand. The fluid valves are calibrated to operate differently depending on the degree of movement inertia which cannot be duplicated by hand.
Do BILSTEIN shocks have a break in period?
I have noticed that Bilstein’s do have a break-in period. At a 1000 miles I’d have thought that you’d be past that by then, but perhaps not. As with anything, the higher the performance, the more narrow minded and potentially finicky they become.
How are shocks supposed to be mounted?
Ultimately: don’t mount shocks upside down just because it looks cool. Sometimes a shock must be mounted upside down due to space limitations, or to protect the shock body, if this is the case, make sure you use a shock designed to be mounted upside down.
Can I adjust my Bilstein 5100 after they are installed?
The adjustable 5100 fronts have a groove in the shock where a ring sits in. Then your perch rests on top of that. Spring is then compressed on top of that. You will have to completely disassemble the shock then reinstall everything after changing the height setting.
Will Bilstein rear shocks lift your truck?
Yes. In many cases there is an option for a no lift setting on the struts and a 0″ lifted shock that will work with stock height trucks. The stock height shock will normally cover a 0″ (Stock Height) to 1″ lift.
How long does it take to install Bilstein 5100?
Thanks in advance. 45 minutes for each side in the front, 45 minutes total for both sides in the back, so 2-2.5 hours total.
Why do people install shocks upside down?
Sometimes a shock must be mounted upside down due to space limitations, or to protect the shock body, if this is the case, make sure you use a shock designed to be mounted upside down.
How to install Bilstein 5160 series reservoir shocks?
Engineered specifically for each truck,SUV,and lift height
Where to rebuild Bilstein shocks?
Bilstein off-road shocks, like the 7100 Series, can be rebuilt in your garage with minimal tools. They were designed for racing, so they are serviceable out in the field. All the rebuild parts can…
How to install Gabriel shocks?
How to Install Gabriel Shocks. Place a jack under the frame directly in front of the driver’s rear wheel. Remove the lug nuts from the wheel using a tire iron and pull the wheel off the vehicle. Locate the bottom through bolt that secures the lower portion of the OEM shock to the suspension shock mount. Read, more elaboration about it is given
How to install lowering springs on original shocks?
Install the spring. Since lowering springs are made to work with your factory suspension, you will just put the new lowering spring in the same place as the old coil spring. Fasten it in the same way as the old coil spring before reattaching other hardware.
