How do I fix my TimberTech?

For deep scratches in TimberTech decking, the application of heat with a soldering iron or heat gun can make the damaged area less visible. If using a soldering iron, slide the rounded point of the tip of the soldering iron into the scratch. The scratched area will melt and return to its original color.

Is it OK to pressure wash TimberTech decking?

A power washer can be used for RINSING ONLY with TimberTech Deck or Porch. The recommended maximum pressure is 1,500 psi. A fan tip nozzle should be used. Spray in the direction of the grain pattern, never across the grain, to avoid damaging the product.

How do you get scratches out of TimberTech decking?

For example, TimberTech (800-307-7780, www.timbertech.com ) recommends using a wire brush to smooth over scratches in its wood-plastic composites (TwinFinish, ReliaBoard, DockSider and certain colors of Floorizon).

Can composite decking be repaired?

If the boards on your composite deck have chips or small cracks, you may be able to repair them by using a composite deck repair kit — depending on the materials and the manufacturer of your deck’s boards.

Can you use Dawn to clean composite decking?

For grease and oil stains, apply a few drops of liquid dish detergent such as Dawn. This will power through the grease and lift it from the surface without damaging the composite decking. Use a handheld scrub brush dipped in warm water to whisk away the oily stain.

Can you use bleach on TimberTech?

For all-purpose cleaning: TimberTech® DeckCleaner™. For power cleaning: A cleaner containing chlorine bleach (sodium hypochlorite or calcium hypochlorite) to dissolve mold, mildew, and other organic materials. Note that the excessive use of bleach can damage the wood, leaving an unnatural whitewashed appearance.

Does TimberTech AZEK scratch easily?

Both Timbertech composite and PVC decking boards are scratch-resistant, not scratch-proof. This means they can easily get scratched by weather, furniture, shoes, kids, and pets. Surface scratches will fade and wear down over time, but deeper scratches can be repaired with a heat gun or epoxy filler.

Will dog claws scratch composite decking?

A large dog’s claws will easily scratch an uncapped composite decking. Without the cap, the wood fibres will readily soak up the dog’s urine and emit a terrible odour in the sun. The only advantage un-capped composite has over cedar decking is fewer splinter.

How do you repair a split composite deck?

Sand the crack and filler using a hand-block with 100-grit sandpaper. Use strokes parallel to the board to sand the filler flush with the surface of the crack. If the filler has shrunk and created a slight depression, fill the depression with more composite filler and let it dry.

Why is my composite decking lifting?

The reason why most composites warp is due to thermal expansion. When plastic fibres of the composites get heated, they will expand. It will return to its original size unless there’s a problem with the decking board spacing.

How do you revive a composite deck?

Combine half a cup of apple cider or white wine vinegar with a gallon of water and a cup of baking soda — this is the cleaning solution recommended by Trex for its decking boards. Spray down the deck, being careful to cover the entire area with the solution.

Is OxiClean good for cleaning composite decks?

Unlike chlorine bleach, OxiClean uses oxygen ions to clean, which are safe for use on composite decking. SimpleGreen uses biodegradable non-toxic ingredients, which aren’t as harsh as bleach and other cleaners, making it safe for use on composite decking.

Can I use vinegar on composite deck?

When cleaning your deck, make sure you only use oxygen bleach and not chlorine bleach, which can compromise the structural integrity of your wood deck. Vinegar – Safe for both composite and wood decking, mix a half-cup of white vinegar or apple cider vinegar to ¼ a cup of baking soda with 1 gallon of water.

Can you fix warped composite decking?

In most cases, fixing a warped composite decking requires the replacement of each individually warped board. Here are the steps on how to do it. First, you will want to identify the parts of your decking that require replacement. Then, measure the composite boards that you will replace.

How do I stop my composite deck from scratching?

Make use of furniture leg pads Heavy furniture or furniture with metal legs is particularly susceptible to causing scratches, so it’s best to protect your deck with furniture leg pads. There are a lot of different kinds of furniture leg pads on the market including rubber, plastic, foam etc.