What angle should a door architrave be?

45-degree
Most often, internal doors are perfectly square, and this means you only need to cut standard 45-degree mitre joints into the architrave to properly install it.

How much gap do you need around architrave?

You want to leave about 5-10 mm of frame showing once the architrave is attached, this is called the reveal. It’s best to mark this on the frame so you’ll know where to place the architrave when it’s been cut.

What is standard architrave size?

The most common architrave width we see is 70mm (approximately 3 inches). This is due to the majority of people have 6 inch skirting or shorter within their homes. 70mm architrave tends to suit skirtings of this height.

How is architrave attached?

The headpiece of the architrave is usually fitted first. Measure the line across the top of the door between intersections and mark the length onto the inner edge of your architrave piece. Architrave is joined with mitre cuts, so remember to account for the longer edge when you’re measuring up.

Can I use skirting board as architrave?

So in short there are no major differences between architrave and skirting boards except the end finish. This is great as in most cases you can match your skirting board and architrave to achieve a complete look that’s cohesive.

Does architrave go to the floor?

Conclusion. As you can see, architrave is always fitted down to the floor. The only caveat to this, is if you are using plinth blocks.

How do you choose architrave width?

Choosing the width If your frame is close to the wall you must measure to see if your chosen architrave will fit. 70mm width – This is the most common architrave width in British homes. This is because the majority of people have 150mm or shorter skirting boards, so the 70mm architrave suits skirtings of this height.

How do you calculate architrave?

Measure from the first internal corner to the edge of door opening. Write down this measurement. Tip~ Do not measure to the point where your architrave will finish once installed, or where your architrave starts if you’re measuring a room with mouldings already installed. This allows for wastage.

Do you fit architrave before plastering?

We always recommend fitting skirting and architraves after the plaster has dried. If you are applying backing plasters e.g; Bonding Coat etc..

How thick should architrave be?

18mm thickness – This is the most commonly chosen architrave thickness, and is found in many homes throughout the UK.

Should architrave be wider than skirting?

We would normally recommend that the skirting is approximately double the width of the architrave. For example if your architrave is 90mm wide the skirting should be at least 180mm high. Darker skirting will be more noticeable than white painted so this should be considered when choosing the height.

What goes on first skirting or architrave?

Quite simply skirting boards are used to cover the join between the wall and the floor, whilst architrave is used to edge interior doors, windows and loft hatches. If you’re fitting architrave and skirting then fit the architrave first.

Should architrave go to the floor?

The usual method with that is to cut the skirting boards back by the width of the architrave, so that the architraves go down to the floor with the skirting butting up to it.

Should architrave be same thickness as skirting?

How do you measure and cut a door for architrave?

Measure from the floor to the bottom edge of the headpiece and mark this distance on the two sections of architrave that will be your side pieces. Then mark the intended direction of the mitre cut on the architrave. Remember that the bottom end of each side piece will have a simple square cut.

Should architrave be deeper than skirting?

Do you glue architrave?

Apply PVA glue to your top architrave on the end that will touch the side architrave. Hold in place and nail as you did the side, making sure the two pieces are perfectly lined up and you have your 3mm gap. For the remaining side, repeat this process but start from the mitre and work your way down.

What is a door architrave?

Door architrave is a decorative mouldering that is used to further enhance the appearance of your door frame. They are able to conceal the join between the wall and the frame of the door.

How far back should an architrave be from a door?

2. Mark Out Architrave Lines The architrave must be set 6 mm back from the frame of the door. You’ll want to set your combination square to 6 mm and then mark out 6 mm around the door frame and above the door frame.

How do you attach an architrave to a door frame?

Run a bead of wood glue all the way down the piece of architrave. Align the architrave perfectly with the 6 mm margins you marked out earlier. Hammer in one of the oval nails to fix the architrave to the door frame. Do not fully hit the oval nails in.

What makes a great architrave?

High above windows and doors, architraves work to add grandeur to any space – reducing miter lines and elevating your look. A great architrave is, above all else, the dressing that’s built to impress. 1. Atmosphere Interior Design Atmosphere Interior Design is known for their attention to detail and classic proportions.